View IP4064CX8LFP_4563638.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection to IEC 61000-4-2 level 4
Rev. 02 -- 11 February 2010 Product data sheet
1. Product profile
1.1 General description
The IP4064CX8, IP4364CX8 and IP4366CX8 are 3-channel RC low-pass filter arrays which are designed to provide filtering of undesired RF signals in the 800 MHz to 3 000 MHz frequency band. In addition, the IP4064CX8, IP4364CX8 and IP4366CX8 incorporate diodes to provide protection to downstream components from ElectroStatic Discharge (ESD) voltages as high as 15 kV contact discharge according the IEC 61000-4-2 model, far exceeding standard level 4. All three devices are fabricated using monolithic silicon technology and integrate three resistors and seven high-level ESD-protection diodes in a single Wafer-Level Chip-Scale Package (WLCSP). These features make the IP4064CX8, IP4364CX8 and IP4366CX8 ideal for use in applications requiring the utmost in miniaturization such as mobile phone handsets, cordless telephones and personal digital devices.
1.2 Features and benefits
Pb-free, RoHS compliant and free of halogen and antimony (Dark Green compliant) 3-channel SIM card interface integrated RC filter array Integrated 100 /100 /47 series channel resistors Integrated ESD protection withstanding 15 kV contact discharge, far exceeding IEC 61000-4-2 level 4 WLCSP with 0.4 mm pitch (IP4364CX8 and IP4366CX8) and 0.5 mm pitch (IP4064CX8)
1.3 Applications
SIM interfaces in e.g. cellular and Personal Communication System (PCS) mobile handsets
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
2. Pinning information
2.1 Pinning
bump A1 index area 1 A B 2 3
C
008aaa206
transparent top view, solder balls facing down
Fig 1.
Pin configuration
2.2 Pin description
Table 1. Pin A1 A2 A3 B1 B2 B3 C1 C2 C3 Pinning Description not connected (missing ball) external pin 1 internal pin 1 external pin 2 ground internal pin 2 external pin 3 supply ESD protection internal pin 3
3. Ordering information
Table 2. Ordering information Package Name IP4064CX8/LF/P IP4364CX8/LF/P IP4366CX8/P WLCSP8 WLCSP8 WLCSP8 Description wafer level chip-size package; 8 bumps; 1.41 x 1.41 x 0.65 mm wafer level chip-size package; 8 bumps; 1.16 x 1.16 x 0.61 mm wafer level chip-size package; 8 bumps; 1.16 x 1.16 x 0.61 mm Version IP4064CX8/LF/P IP4364CX8/LF/P IP4366CX8/P Type number
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
2 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
4. Functional diagram
C2
R1
A3
100 R2
A2
B3
47 R3
B1
C3 IEC61000-4-2 level 1 protection pins
100
C1 IEC61000-4-2 level 4 protection pins
008aaa210
B2
Fig 2.
Schematic diagram
5. Limiting values
Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VI VESD Parameter input voltage electrostatic discharge voltage pins A2, B1, C1 and C2 to ground contact discharge air discharge IEC 61000-4-2 level 4; pins A2, B1, C1 and C2 to ground contact discharge air discharge IEC 61000-4-2 level 1; pins A3, B3 and C3 to ground contact discharge air discharge Pch Ptot Tstg Tamb
[1]
[1] [1]
Conditions
Min -0.5
Max +5.5
Unit V
-15 -15
+15 +15
kV kV
-8 -15
+8 +15
kV kV
-2 -2 -55
+2 +2 60 180 +150 260 +85
kV kV mW mW C C C
channel power dissipation total power dissipation storage temperature
continuous power; Tamb = 70 C continuous power; Tamb = 70 C 10 s maximum
Treflow(peak) peak reflow temperature ambient temperature
-35
Device is qualified with 1000 pulses of 15 kV contact discharges each, according to the IEC61000-4-2 model and far exceeds the specified level 4 (8 kV contact discharge).
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
3 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
6. Characteristics
Table 4. Electrical characteristics Tamb = 25 C; unless otherwise specified. Symbol Parameter Rs(ch) Cch Conditions R2 channel capacitance including diode capacitance; Vbias(DC) = 0 V; f = 1 MHz IP4064CX8 IP4364CX8 IP4366CX8 VBR ILR
[1]
[1]
Min 75 35.2
Typ 100 47.0
Max 125 58.8
Unit
channel series resistance R1 and R3
14 14 8 6 -
17 17 10 -
20 20 12 10 50
pF pF pF V nA
breakdown voltage reverse leakage current
Guaranteed by design.
Itest = 1 mA VI = 3 V
7. Application information
7.1 Application diagram
A typical application diagram showing IP4064CX8, IP4364CX8 or IP4366CX8 in a SIM card interface is depicted in Figure 3. The 2 kV ESD compliant pins (A3, B3 and C3) are connected to the baseband interface side while the four 15 kV ESD compliant pins (A2, B1, C1 and C2) are connected to the SIM card.
VSIM
C2 RST A3
R1 100
VCC A2
GND
RST
SPU
CLK
B3
R2 47
B1
CLK
I/O
I/O
C3
R3 100
C1
AUX1 AUX2
baseband
B2
SIM card
008aaa211
Fig 3.
Typical application diagram
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
4 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
7.2 Insertion loss
The IP4064CX8, IP4364CX8 and IP4366CX8 are mainly designed as an EMI/RFI filter for SIM card interfaces. The insertion loss measurement configuration of a typical 50 NetWork Analyzer (NWA) system for evaluation of the IP4064CX8, IP4364CX8 and IP4366CX8 is shown in Figure 4. The insertion loss in a 50 NWA system for all three channels of IP4064CX8 and IP4364CX8 is depicted in Figure 5a while insertion loss of IP4366CX8 is shown in Figure 5b. The insertion loss is measured with a test Printed-Circuit Board (PCB) utilizing laser drilled micro-via holes that connect the PCB ground plane to the ground pins.
IN
50
DUT
OUT
50
TEST BOARD
Vgen 001aai755
Fig 4.
Frequency response measurement configuration
0 s21 (dB) -10
001aag219
0 s21 (dB)
008aaa207
(1)
(1)
-10
-20
-20
(2)
(2)
(3)
-30
(3)
-30
-40 10-1
1
10
102
103 104 f (MHz)
-40 10-1
1
10
102
103 104 f (MHz)
(1) Channel B1 to B3. (2) Channel A2 to A3. (3) Channel C1 to C3.
a. IP4064CX8 and IP4364CX8 Fig 5. Measured insertion loss magnitudes
b. IP4366CX8
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
5 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
7.3 Crosstalk
The crosstalk measurement configuration of a typical 50 NWA system for evaluation of the IP4064CX8, IP4364CX8 and IP4366CX8 is shown in Figure 6. Four typical examples of crosstalk measurement results of IP4064CX8 and IP4364CX8 are depicted in Figure 7a. The crosstalk behavior of IP4366CX8 is shown in Figure 7b. Unused channels are terminated with 50 to ground.
IN_1
50
DUT
OUT_2 OUT_1
50 50
IN_2
50
TEST BOARD
Vgen 001aai756
Fig 6.
Crosstalk measurement configuration
0 ct (dB) -20
008aaa208
0 ct (dB) -20
(1) (2) (3) (4) (5) (6)
008aaa209
-40
(1) (2) (3) (4)
-40
-60
-60
-80
-80
-100
1
10
102
103 f (MHz)
104
-100
1
10
102
103 f (MHz)
104
(1) Pin C1 to pin B3. (2) Pin B1 to pin C3. (3) Pin B1 to pin A3. (4) Pin A2 to pin C3.
(1) Pin B1 to pin C3. (2) Pin A2 to pin B3. (3) Pin B1 to pin A3. (4) Pin A2 to pin C3. (5) Pin C2 to pin A3. (6) Pin C2 to pin C3.
a. IP4064CX8 and IP4364CX8 Fig 7. Measured crosstalk between different channels
b. IP4366CX8
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
6 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
8. Package outline
WLCSP8: wafer level chip-size package; 8 bumps (3 x 3 - A1)
D
bump A1 index area A2 E A A1
detail X
e1 e b
C e B e1
A
1 European projection
2
3 X
wlcsp8_3x3-a1_po
Fig 8.
Package outline (WLCSP8)
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
7 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
Dimensions for Figure 8 Min 0.60 0.22 0.38 0.27 1.36 1.36 0.56 0.18 0.38 0.21 1.11 1.11 Typ 0.65 0.24 0.41 0.32 1.41 1.41 0.5 1.0 0.61 0.20 0.41 0.26 1.16 1.16 0.4 0.8 Max 0.70 0.26 0.44 0.37 1.46 1.46 0.66 0.22 0.44 0.31 1.21 1.21 Unit mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
Table 5. Symbol IP4064CX8 A A1 A2 b D E e e1
IP4364CX8 and IP4366CX8 A A1 A2 b D E e e1
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
8 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
9. Soldering of WLCSP packages
9.1 Introduction to soldering WLCSP packages
This text provides a very brief insight into a complex technology. A more in-depth account of soldering WLCSP (Wafer Level Chip-Size Packages) can be found in application note AN10439 "Wafer Level Chip Scale Package" and in application note AN10365 "Surface mount reflow soldering description". Wave soldering is not suitable for this package. All NXP WLCSP packages are lead-free.
9.2 Board mounting
Board mounting of a WLCSP requires several steps: 1. Solder paste printing on the PCB 2. Component placement with a pick and place machine 3. The reflow soldering itself
9.3 Reflow soldering
Key characteristics in reflow soldering are:
* Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 9) than a PbSn process, thus reducing the process window
* Solder paste printing issues, such as smearing, release, and adjusting the process
window for a mix of large and small components on one board
* Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature), and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic) while being low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 6.
Table 6. Lead-free process (from J-STD-020C) Package reflow temperature (C) Volume (mm3) < 350 < 1.6 1.6 to 2.5 > 2.5 260 260 250 350 to 2 000 260 250 245 > 2 000 260 245 245
Package thickness (mm)
Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 9.
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
9 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
temperature
maximum peak temperature = MSL limit, damage level
minimum peak temperature = minimum soldering temperature
peak temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 9.
Temperature profiles for large and small components
For further information on temperature profiles, refer to application note AN10365 "Surface mount reflow soldering description".
9.3.1 Stand off
The stand off between the substrate and the chip is determined by:
* The amount of printed solder on the substrate * The size of the solder land on the substrate * The bump height on the chip
The higher the stand off, the better the stresses are released due to TEC (Thermal Expansion Coefficient) differences between substrate and chip.
9.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been wetted by the solder from the bump. The surface of the joint should be smooth and the shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps after reflow can occur during the reflow process in bumps with high ratio of bump diameter to bump height, i.e. low bumps with large diameter. No failures have been found to be related to these voids. Solder joint inspection after reflow can be done with X-ray to monitor defects such as bridging, open circuits and voids.
9.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the chip from the substrate and replacing it with a new chip. If a chip is removed from the substrate, most solder balls of the chip will be damaged. In that case it is recommended not to re-use the chip again.
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
10 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
Device removal can be done when the substrate is heated until it is certain that all solder joints are molten. The chip can then be carefully removed from the substrate without damaging the tracks and solder lands on the substrate. Removing the device must be done using plastic tweezers, because metal tweezers can damage the silicon. The surface of the substrate should be carefully cleaned and all solder and flux residues and/or underfill removed. When a new chip is placed on the substrate, use the flux process instead of solder on the solder lands. Apply flux on the bumps at the chip side as well as on the solder pads on the substrate. Place and align the new chip while viewing with a microscope. To reflow the solder, use the solder profile shown in application note AN10365 "Surface mount reflow soldering description".
9.3.4 Cleaning
Cleaning can be done after reflow soldering.
10. Abbreviations
Table 7. Acronym DUT EMI ESD NWA PCB PCS RFI RoHS SIM WLCSP Abbreviations Description Device Under Test ElectroMagnetic Interference ElectroStatic Discharge NetWork Analyzer Printed-Circuit Board Personal Communication System Radio Frequency Interference Restriction of Hazardous Substances Subscriber Identity Module Wafer-Level Chip-Scale Package
11. Revision history
Table 8. Revision history Release date 20100211 Data sheet status Change notice Supersedes Product data sheet IP4064CX8LF_IP4364CX8LF_1 Document ID IP4064CX8_IP4364CX8_ IP4366CX8_2 Modifications:
* * *
Type number IP4366CX8 added Figure 3: added General editorial update Product data sheet -
IP4064CX8LF_IP4364CX8LF_1 20071112
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
11 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
12. Legal information
12.1 Data sheet status
Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet
[1] [2] [3]
Product status[3] Development Qualification Production
Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification.
Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
12.2 Definitions
Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.
malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on a weakness or default in the customer application/use or the application/use of customer's third party customer(s) (hereinafter both referred to as "Application"). It is customer's sole responsibility to check whether the NXP Semiconductors product is suitable and fit for the Application planned. Customer has to do all necessary testing for the Application in order to avoid a default of the Application and the product. NXP Semiconductors does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Non-automotive qualified products -- Unless the data sheet of an NXP Semiconductors product expressly states that the product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the
(c) NXP B.V. 2010. All rights reserved.
12.3 Disclaimers
Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
Product data sheet
Rev. 02 -- 11 February 2010
12 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications.
12.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
13. Contact information
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
IP4064CX8_IP4364CX8_IP4366CX8_2
All information provided in this document is subject to legal disclaimers.
(c) NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 02 -- 11 February 2010
13 of 14
NXP Semiconductors
IP4064CX8; IP4364CX8; IP4366CX8
Integrated SIM card passive filter array with ESD protection
14. Contents
1 1.1 1.2 1.3 2 2.1 2.2 3 4 5 6 7 7.1 7.2 7.3 8 9 9.1 9.2 9.3 9.3.1 9.3.2 9.3.3 9.3.4 10 11 12 12.1 12.2 12.3 12.4 13 14 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Application information. . . . . . . . . . . . . . . . . . . 4 Application diagram . . . . . . . . . . . . . . . . . . . . . 4 Insertion loss . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Crosstalk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 7 Soldering of WLCSP packages. . . . . . . . . . . . . 9 Introduction to soldering WLCSP packages . . . 9 Board mounting . . . . . . . . . . . . . . . . . . . . . . . . 9 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . . 9 Stand off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Quality of solder joint . . . . . . . . . . . . . . . . . . . 10 Rework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11 Legal information. . . . . . . . . . . . . . . . . . . . . . . 12 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 12 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contact information. . . . . . . . . . . . . . . . . . . . . 13 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'.
(c) NXP B.V. 2010.
All rights reserved.
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 11 February 2010 Document identifier: IP4064CX8_IP4364CX8_IP4366CX8_2

▲Up To Search▲

Price & Availability of IP4064CX8LFP

	To Download IP4064CX8LFP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .